|
|
(12 dazwischenliegende Versionen des gleichen Benutzers werden nicht angezeigt) |
Zeile 1: |
Zeile 1: |
− | | + | Ich bin nicht mehr aktiv im Verein. |
− | == About me ==
| + | |
− | | + | |
− | [[File:76001 318186104966806 1026016756 n.jpg|200px]]
| + | |
− | | + | |
− | MAIL: [mailto:stefan@attraktor.org stefan@attraktor.org]
| + | |
− | | + | |
− | XMPP: [mailto:stefan@makerspace.hamburg stefan@makerspace.hamburg]
| + | |
− | | + | |
− | | + | |
− | === X-Application in full screen on Raspberry Pi / BeagleBone Black/White ===
| + | |
− | | + | |
− | /usr/bin/xinit $PROGRAM -- -dpms -s 0 -nocursor
| + | |
− | | + | |
− | Options ''-dpms'' and ''-s 0'' turn off screen saver, option ''-nocursor'' hides the mouse cursor.
| + | |
− | | + | |
− | === Info-Beamer mit systemd ===
| + | |
− | | + | |
− | <pre>
| + | |
− | [Unit]
| + | |
− | Description=Info-Beamer
| + | |
− | After=network.target
| + | |
− | | + | |
− | [Service]
| + | |
− | ExecStart=/usr/local/bin/info-beamer /home/pi/info-beamer/active
| + | |
− | Restart=on-failure
| + | |
− | | + | |
− | [Install]
| + | |
− | WantedBy=multi-user.target
| + | |
− | </pre>
| + | |
− | | + | |
− | === SocketCAN ===
| + | |
− | | + | |
− | Virtueller Bus:
| + | |
− | | + | |
− | sudo modprobe vcan
| + | |
− | sudo ip link add dev vcan0 type vcan
| + | |
− | sudo ip link set up vcan0
| + | |
− | | + | |
− | === Linksammlung ===
| + | |
− | | + | |
− | * [http://physicus.free.fr/observatoire/presentation.php Geo-Magnetometer]
| + | |
− | * [http://wp.boim.com/?p=94 Calibration tools for Delta 3D printers]
| + | |
− | | + | |
− | === Eagle nach G-Code ===
| + | |
− | * pcb2gcode
| + | |
− | | + | |
− | sudo aptitude install build-essential autoconf libtool gerbv libboost-dev libboost-program-options-dev libglibmm-2.4-dev libgtkmm-2.4-dev
| + | |
− | git clone git://pcb2gcode.git.sourceforge.net/gitroot/pcb2gcode/pcb2gcode
| + | |
− | cd pcb2gcode
| + | |
− | autoreconf
| + | |
− | ./configure
| + | |
− | make
| + | |
− | | + | |
− | Vorsicht, pcb2gcode rechnet alles in Inches!
| + | |
− | | + | |
− | ==== Script zur Erstellung von GCode aus Eagle-Files [[media:pcbcam.gz]] ====
| + | |
− | | + | |
− | Das Skript erzeugt aus einem Eagle-Board-File (Endung .brd) mehrere G-Code-Files und Postscript-Files für die Erstellung der Lötstoppmaske. Die erzeugten Dateien sind im Einzelnen:
| + | |
− | | + | |
− | ; back.ngc : Lötseite
| + | |
− | ; front.ngc : Bestückungsseite
| + | |
− | ; outline.ngc : Ausfräsung der Platine
| + | |
− | ; drill.ngc : Bohrungen
| + | |
− | ; back_stop.ps : Lötstoppmaske Lötseite
| + | |
− | ; front_stop.ps : Lötstoppmaske Bestückungsseite
| + | |
− | | + | |
− | = Spielen =
| + | |
− | | + | |
− | - {{Calendar-iCal}}
| + | |
− | | + | |
− | = Alles =
| + | |
− | | + | |
− | {{Special:PrefixIndex/{{FULLPAGENAME}}/}}
| + | |
Ich bin nicht mehr aktiv im Verein.